{"id":335,"date":"2026-08-20T12:58:35","date_gmt":"2026-08-20T12:58:35","guid":{"rendered":"https:\/\/crewood.net\/?p=335"},"modified":"2026-08-20T12:58:35","modified_gmt":"2026-08-20T12:58:35","slug":"bending-meccano","status":"publish","type":"post","link":"https:\/\/crewood.net\/?p=335","title":{"rendered":"Bending Meccano"},"content":{"rendered":"\n<p class=\"wp-block-paragraph\">Draft version without photos, August 2026<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Does anyone like bending their precious Meccano parts? I&#8217;d guess not. But to build lots of Meccano models means you need to bend parts, preferably in such a way that you can bend them back again later. Here&#8217;s how I go about it.<\/p>\n\n\n\n<h6 class=\"wp-block-heading\">Bending flexible plates<\/h6>\n\n\n\n<p class=\"wp-block-paragraph\">This is really not too difficult. The key thing to avoid is creasing the plate, as you&#8217;ll never get the crease out again. Creases will form easily through the holes of the plate, so you need to concentrate on getting the bend between the holes, rather than through them. I just use fingers and thumbs to gradually coax the plate to the right curve. For each size of plate I&#8217;ve got some that I never bend, some that I&#8217;ve bent repeatedly but gently, and a few that will never be flat again, but are useful if a model requires a plate that may never recover, e.g. a bend that is more like a right-angle than a gradual curve. There are some out there.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">I don&#8217;t always bend the plate flat again afterwards, unless I need to in order to fit it back in its box.<\/p>\n\n\n\n<h6 class=\"wp-block-heading\">Bending angle brackets<\/h6>\n\n\n\n<p class=\"wp-block-paragraph\">Again, this is pretty easy, and needs doing every now and then. A pair of long nose pliers generally does the job. I keep my obtuse angle brackets unbent, and always have a few plain 1\/2&#8243; brackets bent at various angles from previous models.<\/p>\n\n\n\n<h6 class=\"wp-block-heading\">Bending strips<\/h6>\n\n\n\n<p class=\"wp-block-paragraph\">This is where you need a set of steel rollers built into a rolling machine. If you try to bend a strip without rollers it will bend through the holes, not evenly along the strip.  It won&#8217;t look good, it will weaken the metal, and it will never look straight again. I bought my rollers from <a href=\"http:\/\/www.meccanohobby.co.uk\/\" data-type=\"link\" data-id=\"http:\/\/www.meccanohobby.co.uk\/\" target=\"_blank\" rel=\"noreferrer noopener\">John Thorpe<\/a> and built my own <a href=\"https:\/\/crewood.net\/?p=46\" data-type=\"post\" data-id=\"46\">rolling machine<\/a>. It will put an even bend into a strip and will straighten the strip out again afterwards. You just need to put the bend in gradually, not all at once.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A word of caution if you&#8217;re using very old strips. It&#8217;s not happened to me, but I understand early strips, I&#8217;d imagine from the nickel plate era, tend to snap rather than bend.<\/p>\n\n\n\n<h6 class=\"wp-block-heading\">Bending flat plates<\/h6>\n\n\n\n<p class=\"wp-block-paragraph\">Flat plates don&#8217;t bend easily, but some of the Super Models, for instance, require curves in plates. You can often replace the flat plates with flexible plates, if you&#8217;re happy to do that, but that&#8217;s not always a solution as the plates can be structural, or the model may need holes in the plates that aren&#8217;t there in a flexible plate. Anyway, I&#8217;m trying to build accurately to the Super Model specifications, so I need to bend flat plates.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The solution is again to use a set of rollers. My strip roller is only 3&#8243; wide, but for the plates in the <a href=\"https:\/\/crewood.net\/?p=137\" data-type=\"post\" data-id=\"137\">Baltic Tank Loco<\/a> I needed to bend a number of 5 1\/2&#8243; by 3 1\/2&#8243; plates, so I went back to John Thorpe, bought a set of his 6&#8243; rollers, and built a <a href=\"https:\/\/crewood.net\/?p=133\" data-type=\"post\" data-id=\"133\">sturdier bending machine<\/a>. This did the job, which to be honest surprised me. I was pretty sure John&#8217;s rollers were up to the job, but I thought my Meccano rolling machine would probably explode. It didn&#8217;t.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">You do need to be patient though. The bend needs to be put in very gradually, and the rolling machine will probably need a fair bit of maintenance as you go along. It has to take a lot of pressure.<\/p>\n\n\n\n<h6 class=\"wp-block-heading\">Bending rods<\/h6>\n\n\n\n<p class=\"wp-block-paragraph\">There&#8217;s no straightening out a bent rod. The Baltic Tank Loco Super Model requires an 8&#8243; rod bent nearly into a semicircle though, so I had to sacrifice one. To bend it I used a Workmate, a vice, a length of steel pipe and a pair of mole grips. I got the job done, but I wouldn&#8217;t recommend it as a way of life.<\/p>\n","protected":false},"excerpt":{"rendered":"<p>Draft version without photos, August 2026 Does anyone like bending their precious Meccano parts? I&#8217;d guess not. But to build lots of Meccano models means you need to bend parts, preferably in such a way that you can bend them back again later. Here&#8217;s how I go about it. Bending flexible plates This is really &hellip; <a href=\"https:\/\/crewood.net\/?p=335\" class=\"more-link\">Continue reading<span class=\"screen-reader-text\"> &#8220;Bending Meccano&#8221;<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[9],"tags":[],"class_list":["post-335","post","type-post","status-publish","format-standard","hentry","category-tools-and-techniques"],"_links":{"self":[{"href":"https:\/\/crewood.net\/index.php?rest_route=\/wp\/v2\/posts\/335","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/crewood.net\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/crewood.net\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/crewood.net\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/crewood.net\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=335"}],"version-history":[{"count":2,"href":"https:\/\/crewood.net\/index.php?rest_route=\/wp\/v2\/posts\/335\/revisions"}],"predecessor-version":[{"id":343,"href":"https:\/\/crewood.net\/index.php?rest_route=\/wp\/v2\/posts\/335\/revisions\/343"}],"wp:attachment":[{"href":"https:\/\/crewood.net\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=335"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/crewood.net\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=335"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/crewood.net\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=335"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}