{"id":332,"date":"2026-08-20T12:59:22","date_gmt":"2026-08-20T12:59:22","guid":{"rendered":"https:\/\/crewood.net\/?p=332"},"modified":"2026-08-20T13:33:11","modified_gmt":"2026-08-20T13:33:11","slug":"repainting-meccano","status":"publish","type":"post","link":"https:\/\/crewood.net\/?p=332","title":{"rendered":"Repainting Meccano"},"content":{"rendered":"\n<h2 class=\"wp-block-heading\">Introduction<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Draft version without photos, August 2026<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">I want to build models that look good, without spending a fortune on parts in mint condition. Also, I&#8217;d rather be using original Meccano parts where practical, although I&#8217;m not too dogmatic about that, and I&#8217;ve got quite a few reproduction parts.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">In my view, a model looks at its best if its parts all match the same era of Meccano, particularly if the model is a recreation of a model to a Meccano design.  My starting point was a 1950 or 1951 Outfit 10, so my main focus is on building models that use the colour scheme from that time: early post-war red and green.  Most of that No. 10 Outfit is still in pretty good condition, but, since I&#8217;m aiming to build the entire set of 1920s\/30s Super Models, I&#8217;ve had to buy a lot of additional parts, and I wanted them in early post-war red and green too. By buying bargain lots in dodgy condition, from Meccano dealers and an auction house, I&#8217;ve saved a lot of money, but I&#8217;ve ended up with a lot of parts that I&#8217;d not want to use in my models, as the paint&#8217;s in poor condition or the wrong colour. And some of them are pretty rusty too. So I decided to have a go at repainting some of them. So far it&#8217;s gone pretty well, so I thought I&#8217;d document how I&#8217;ve been doing it, in case it would be of use to anyone else.  I&#8217;m not claiming it&#8217;s the best way to go, but it&#8217;s worked for me.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">I&#8217;ve never tried to re-plate with either zinc or nickel so can&#8217;t offer any advice on that.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Where I started<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">I found a <a href=\"https:\/\/selmec.org.uk\/articles\/42-meccano-restoration\" data-type=\"link\" data-id=\"https:\/\/selmec.org.uk\/articles\/42-meccano-restoration\" target=\"_blank\" rel=\"noreferrer noopener\">great article written in 2008 by Allen Berman<\/a> on the South East London Meccano Club website. I didn&#8217;t follow it entirely, particularly once it got to the painting, but it really told me most of what I needed to know. I won&#8217;t repeat what&#8217;s in the article, so you&#8217;ll need to refer to it if you want the full picture of how I&#8217;ve gone about my Meccano refurb. In the sections below I&#8217;ve used the same stage names and numbers as in the original article.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Stage 1 &#8211; Sorting<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Not much to say on this one. I keep the parts I want red separate from the parts I want green of course. I&#8217;ve not yet repainted anything the wrong way round&#8230;<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Most parts are already painted of course, but some are zinc-plated and the odd part is nickel-plated. And some parts have paint over the top of old plating. All the paint has to come off, except when I need to repaint something that&#8217;s in good condition but the wrong colour, so on to the next stage&#8230;<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Stage 2 &#8211; Removing Paint<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Allen Berman used caustic soda to get his paint off. I use Nitromors, and his approach may work better, in that it sounds like it may be less hard work. Caustic soda is nasty stuff though, and I&#8217;m sticking with Nitromors. His recommendation to use a section of guttering to soak the parts is worth considering, but don&#8217;t assume it won&#8217;t leak at the ends.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This stage is physically tiring &#8211; for me, anyway. I put the Nitromors on with a small expendable paintbrush, and remove it with grade 1 steel wire wool. I wear heavy duty rubber gloves, which makes it hard to pick up small parts. When I&#8217;ve finished I wash the parts thoroughly in the kitchen sink and get them properly dry immediately before they start rusting.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Stage 3 &#8211; Removing Old Zinc-plate<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">I haven&#8217;t tried using Spirits of Salts for this. I have tried a few days in vinegar, which works sometimes, but I suspect some of the parts I was trying to strip were nickel-plated. Both sorts of plating seem to be lifted to some extent by phosphoric acid &#8211; see the next section.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Stage 4 &#8211; Removing Rust<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">I sand any nastier bits of rust before soaking, using very fine wet and dry sandpaper &#8211; 600 grade. I use Clarke International Rust Remover from Machine Mart, as recommended by Allen Berman. It&#8217;s phosphoric acid and works well. You&#8217;ll need a plastic box to soak your Meccano in &#8211; one you can pour the rust remover out of for re-use. A jug and a funnel come in handy here. I try to keep the stuff off my hands, but it&#8217;s not unduly caustic, in my experience. It can cause serious stains if spilled though &#8211; I use it in the garage and get it back in the bottles in the garden. It&#8217;s even stained the tarmac.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">After this I wash and dry everything again, then paint quickly before the rust starts again.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">By this time you should know which parts are plated, and whether the plating is flaking off or firmly attached. I get busy with the wire wool and fine sandpaper again, to try to remove anything loose. Normal paints won&#8217;t adhere to plating properly unless it&#8217;s etched to make it rougher.  See below&#8230;<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Stage 5 &#8211; Metal Bashing<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">&#8230;is always good fun&#8230;<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Stage 6 &#8211; Painting<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Thia is where I diverge most from Allen Berman&#8217;s recommendations, in that I use acrylic car paints, sprayed from disposable aerosols. This paint is tough and flexible, and most of what I need is available from my local Halfords.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">You need to make sure you don&#8217;t breathe in any of the paint spray and don&#8217;t paint too much of the surroundings. I paint in the garden, when it&#8217;s not raining, not windy, not too hot and not too cold. That still leaves a fair few days a year that work OK. I don&#8217;t paint in direct sunshine either. I use a proper respirator that filters out organic vapours, not a flimsy Covid-style mask. Mine&#8217;s  a  Swiftlon A1P2 kit with an A1 filter &#8211; they&#8217;re not very expensive and car paint shops sell them.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">I put old dust sheets over a couple of recycling wheely bins and put the hanging rack across the bins, where I can get round both sides of the bins. I follow the instructions on the cans and keep the coats as thin as I can. My routine is:<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li>Spray once with primer, from both sides, and wait 30 minutes.<\/li>\n\n\n\n<li>Turn all parts upside down so you can get at the bits that were inaccessible first time.<\/li>\n\n\n\n<li>Spray again from both sides, and wait an hour.<\/li>\n\n\n\n<li>Repeat steps 1 to 3 with top coat.<\/li>\n\n\n\n<li>Repeat steps 1 to 3 with lacquer.<\/li>\n\n\n\n<li>Get everything out of the weather, e.g. in the garage, still on the rack.<\/li>\n\n\n\n<li>Next day, bring into the house, and leave to harden up for a couple of days before putting away. Carefully, as the paint hasn&#8217;t completely hardened yet.<\/li>\n\n\n\n<li>Give it a couple of weeks before building anything with the newly painted parts.<\/li>\n<\/ol>\n\n\n\n<h5 class=\"wp-block-heading\">Primers<\/h5>\n\n\n\n<p class=\"wp-block-paragraph\">All these are at Halfords:<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li>Grey primer for the green parts.<\/li>\n\n\n\n<li>Red primer for the red parts.<\/li>\n\n\n\n<li>Black primer for those few black parts such as 2&#8243; and 3&#8243; wheels<\/li>\n\n\n\n<li>Etch primer for the parts that still have plating on them. How effective this is I don&#8217;t yet know, but I&#8217;m using it.<\/li>\n<\/ol>\n\n\n\n<h5 class=\"wp-block-heading\">Top coats<\/h5>\n\n\n\n<p class=\"wp-block-paragraph\">This is where relying on Halfords breaks down a bit. There aren&#8217;t many green cars. They do have:<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li>Various red paints, but although they come very close to the right colour, I&#8217;ve not found a perfect match. Audi Brilliant Red isn&#8217;t bad though.<\/li>\n\n\n\n<li>Black Satin, which is great for wheels.<\/li>\n\n\n\n<li>Lacquer, which adds gloss over your top coat, and I use this over my reds and greens.<\/li>\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\">Which left me looking for a good match for Meccano post-war green, and ideally a better match for the red. Luckily there are car paint shops that will match your colour, mix the paint and fill aerosols for you. The one I found was <a href=\"https:\/\/cityautopaints.co.uk\/\" data-type=\"link\" data-id=\"https:\/\/cityautopaints.co.uk\/\" target=\"_blank\" rel=\"noreferrer noopener\">City Auto Paints<\/a> in Hereford. It was a bit of a drive for me, but I shouldn&#8217;t need to go down again now I know the colours I need as they post out. I took sample Meccano parts down to the shop, and matched them to colours on the fan decks in the shop. I took them outside to check them in natural light as well as in the artificial light in the shop. As far as I could see I&#8217;d found perfect matches. They mixed me up three cans of red and three cans of green, with a satin finish. The satin finish gives me control of the level of gloss, as I can add lacquer coats afterwards. They do gloss finish as well of course, but I&#8217;ve not tried that. The final result is as good a match as it possibly could be, as far as I&#8217;m concerned.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The downside, I suppose, is that these aerosols coast about twice that of Halfords cans, but that&#8217;s fair enough really as they are mixed to order. For the record, the colours I ended up using are:<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li>HMG Colorbox Red R0410, 1K Acrylic Satin (PVC17)<\/li>\n\n\n\n<li>HMG Colorbox Green GRE0925, 1K Acrylic Satin (PVC17)<\/li>\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\">I apply two thin coats of primer, two thin coats of top coat, and for the red and green two very thin coats of lacquer. The black I leave with a satin finish. I use hanging racks copied from Allen Berman&#8217;s. You&#8217;ll need strips of wood, staples and wire &#8211; I stripped mains rewiring cable for the wire, as copper can be bent and re-bent over and over.<\/p>\n\n\n\n<h5 class=\"wp-block-heading\">Stage 7 \u2014 Hardening the Paint<\/h5>\n\n\n\n<p class=\"wp-block-paragraph\">After all that work I&#8217;m not going to put my Meccano in the oven &#8211; sorry Allen. I just leave it to harden for a couple of weeks before getting too violent with it, which is normal for car paints.<\/p>\n","protected":false},"excerpt":{"rendered":"<p>Introduction Draft version without photos, August 2026 I want to build models that look good, without spending a fortune on parts in mint condition. Also, I&#8217;d rather be using original Meccano parts where practical, although I&#8217;m not too dogmatic about that, and I&#8217;ve got quite a few reproduction parts. In my view, a model looks &hellip; <a href=\"https:\/\/crewood.net\/?p=332\" class=\"more-link\">Continue reading<span class=\"screen-reader-text\"> &#8220;Repainting Meccano&#8221;<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[9],"tags":[],"class_list":["post-332","post","type-post","status-publish","format-standard","hentry","category-tools-and-techniques"],"_links":{"self":[{"href":"https:\/\/crewood.net\/index.php?rest_route=\/wp\/v2\/posts\/332","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/crewood.net\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/crewood.net\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/crewood.net\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/crewood.net\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=332"}],"version-history":[{"count":5,"href":"https:\/\/crewood.net\/index.php?rest_route=\/wp\/v2\/posts\/332\/revisions"}],"predecessor-version":[{"id":348,"href":"https:\/\/crewood.net\/index.php?rest_route=\/wp\/v2\/posts\/332\/revisions\/348"}],"wp:attachment":[{"href":"https:\/\/crewood.net\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=332"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/crewood.net\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=332"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/crewood.net\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=332"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}